Quiz · Hard
Applied and multi-step questions: stall speed in turns, induced drag, L/D, normal shocks, isentropic relations and compressibility.
A 12,000 N aircraft with m² and flies at sea level (). Its stall speed is about:
21 m/s
42 m/s
59 m/s
30 m/s
m/s. Forgetting the square root or the factor 2 gives the other options.
An aircraft stalls at 100 km/h in level flight. In a steady 60° banked level turn its stall speed is about:
100 km/h
141 km/h
115 km/h
200 km/h
Load factor , and , so km/h. Stall speed is not unchanged: the wing must carry twice the weight.
, , . What is the induced drag coefficient?
0.032
0.125
0.040
0.004
. 0.032 results from forgetting the efficiency factor e.
A jet cruises in level flight at the same CL as it climbs to an altitude where air density is half. True airspeed must change by a factor of:
1.41 (increase)
2.0 (increase)
0.71 (decrease)
1.0 (no change)
: with ρ halved and CL fixed, doubles, so V rises by .
, , . The best lift-to-drag ratio is about:
30
15
7.5
22
. Forgetting the factor of ½ gives 30.
At the speed for maximum L/D, how does induced drag compare with parasite drag?
Induced drag is twice parasite drag
Induced drag is zero
Parasite drag is twice induced drag
They are equal
For a parabolic polar the minimum of in occurs when . Total CD is then .
Normal shock at (γ = 1.4). The static pressure ratio is about:
10.3
9.0
4.5
3.0
. The value 4.5 belongs to M₁ = 2.
A vehicle flies at Mach 2 in air at 216.65 K. Its stagnation (total) temperature is about:
217 K
433 K
390 K
650 K
K. Multiplying by M instead (433 K) is a common slip.
At low speed the minimum pressure coefficient on an airfoil is at . Using Prandtl-Glauert, what is it at ?
-0.48
-0.6
-3.6
-1.0
. Compressibility makes the suction peak stronger.
In a converging duct with supersonic inflow, the flow:
Speeds up and pressure falls
Slows down and pressure rises
Keeps constant velocity
Chokes and becomes sonic everywhere
Supersonic flow behaves opposite to subsonic flow: for a decreasing area decelerates the flow. A supersonic nozzle needs a diverging section.
A convergent-divergent nozzle's back pressure is lowered below the value that first chokes the throat. The mass flow rate:
Keeps increasing
Falls to zero
Stays constant
Doubles
Once the throat is sonic, conditions upstream no longer feel the back pressure. Mass flow depends only on stagnation conditions and throat area.
A 1/10-scale model is tested in a normal-temperature air tunnel. Matching the full-scale Reynolds number at a 100 m/s flight speed would need a tunnel speed of about:
1000 m/s
10 m/s
100 m/s
316 m/s
, so V must rise by 10. That is supersonic, so Mach effects destroy the test. Pressurized or cryogenic tunnels raise ρ or lower μ to fix this.
Why does a dimpled golf ball fly farther than a smooth one of the same size?
Dimples reduce skin friction to zero
Dimples trigger a turbulent boundary layer that delays separation and shrinks the wake
Dimples create lift from the Bernoulli effect only
Dimples make the flow laminar over the whole ball
Form (pressure) drag dominates on a bluff body. A turbulent boundary layer separates later, giving a smaller, lower-drag wake despite higher skin friction.
What is Mach tuck?
A nose-up pitch at stall
A buffet caused by wingtip vortices
The sudden loss of control on supersonic flight due to the sonic boom
A nose-down pitching tendency at high subsonic speed as shocks move aft and the center of pressure shifts rearward
As the shock on the upper surface strengthens and moves aft, the center of pressure moves back, creating a nose-down moment. Mach trim systems compensate.
Why does the area rule reduce transonic wave drag?
A smooth distribution of cross-sectional area along the length reduces shock strength
It reduces the total frontal area of the fuselage
It increases the wing aspect ratio
It prevents boundary layer transition
Wave drag depends on the longitudinal development of total cross-sectional area. Pinching the fuselage near the wing keeps the area change smooth.
A pitot tube in supersonic flow (M > 1) reads:
The freestream total pressure exactly
The static pressure
The total pressure behind a normal bow shock ahead of the probe
Zero, since the flow is supersonic
A detached normal shock forms ahead of the tube. The probe measures the stagnation pressure after the shock, which is lower than the freestream total pressure. The Rayleigh pitot formula corrects for this.
Lift per span on a section is N/m in a flow of m/s and kg/m³. Using Kutta-Joukowski, the circulation is:
20 m²/s
0.08 m²/s
500 m²/s
12.5 m²/s
m²/s.
Doubling the aspect ratio of a wing at constant CL halves the induced drag coefficient.
True
False
is inversely proportional to AR at constant CL and e.
Why is a swept wing prone to tip stall?
The tips have a higher local Mach number than the root only
Spanwise flow thickens the boundary layer toward the tips, and the tips carry high loading aft of the center of gravity
The leading edge sweep reduces the critical angle everywhere equally
Sweep removes the downwash at the tips
Boundary-layer drift outboard and the outboard loading on swept wings lead to early tip separation, causing pitch-up. Fences, vortilons and twist help.