StudyFox
कीमतेंब्लॉगएक्सटेंशनमुफ़्त टूल
  • कीमतें
  • ब्लॉग
  • एक्सटेंशन
  • मुफ़्त टूल
  • शुरू करेंसाइन इन
StudyFox

अपने नोट्स, PDF और स्लाइड्स को फ़्लैशकार्ड, क्विज़, नोट्स और माइंड मैप में बदलें।

StudyFox खोलें

स्टडी टूल्स

  • होमवर्क हेल्पर
  • नोट मेकर
  • फ़्लैशकार्ड मेकर
  • क्विज़ मेकर
  • माइंड मैप मेकर

प्रोडक्ट

  • कीमतें
  • Chrome एक्सटेंशन
  • मुफ़्त एक्सटेंशन
  • स्टडी सेट देखें
  • ब्लॉग

सहायता

  • सहायता केंद्र
  • संपर्क करें
  • गोपनीयता नीति
  • सेवा की शर्तें

तुलना करें

  • Chegg का विकल्प
  • Course Hero का विकल्प
  • Coursology का विकल्प
  • Photomath का विकल्प
  • Gauthmath का विकल्प
  • PhotoSolve का विकल्प
  • CollegeTools का विकल्प
  • Transcript का विकल्प
  • SmartSolve का विकल्प
  • Homeworkify का विकल्प
  • AnswersAi का विकल्प
  • StudyX का विकल्प
  • Quizlet का विकल्प
  • Anki का विकल्प
  • Knowt का विकल्प
  • Brainscape का विकल्प
  • सभी तुलनाएँ

© 2026 StudyFox AI. सर्वाधिकार सुरक्षित।

  • X
  • Discord
  • Instagram
ExploreEngineering & TechMechanical EngineeringMachine Design Quiz: Failure Theories, Gears, Bolts and Bearings

Quiz · Medium

Machine Design Quiz: Failure Theories, Gears, Bolts and Bearings

Mixed concept and calculation questions on von Mises stress, fatigue diagrams, bolted joints, gears, shafts, bearing life and springs.

by Kill h.23 questionsCreated Nov 20, 2026, 08:27 PM
Mechanical Engineering· Machine DesignTags#machine-design#gears#bearings#fatigue

23 questions

  1. 1

    A thin-walled cylinder has p = 2 MPa, r = 0.5 m, t = 10 mm. The hoop stress is:

    • A

      25 MPa

    • B

      50 MPa

    • 100 MPa

    • D

      200 MPa

    sigma = pr/t = 2 x 500/10 = 100 MPa; the axial stress is half that.

  2. 2

    A part sees stress cycling between 100 MPa and 300 MPa. What are the mean and alternating stresses?

    • A

      150 and 150

    • B

      100 and 200

    • C

      300 and 100

    • 200 and 100

    sigma_m = (300 + 100)/2 = 200 MPa; sigma_a = (300 - 100)/2 = 100 MPa.

  3. 3

    A steel part has Sy = 400 MPa. At a critical point σx = 80 MPa and τxy = 40 MPa. By distortion energy, the factor of safety against yielding is about:

    • 3.8

    • B

      1.9

    • C

      5.0

    • D

      0.4

    σ' = sqrt(80^2 + 3 x 40^2) = 105.8 MPa; n = 400/105.8 = 3.8. Using Tresca would give a smaller n (more conservative).

  4. 4

    Which theory is the most conservative for yielding of ductile metals?

    • A

      Distortion energy (von Mises)

    • Maximum shear stress (Tresca)

    • C

      Maximum normal stress

    • D

      Coulomb-Mohr

    Tresca predicts yield slightly earlier than von Mises (Ssy = 0.5Sy vs 0.577Sy). Maximum normal stress and Coulomb-Mohr are for brittle materials.

  5. 5

    A gear module is 3 mm and it has 24 teeth. Its pitch diameter is:

    • A

      8 mm

    • B

      27 mm

    • 72 mm

    • D

      75.4 mm

    d = mN = 3 x 24 = 72 mm. 75.4 mm is the circumference divided by... actually pi x 24 = 75.4, a confusion with circular pitch.

  6. 6

    A 20-tooth pinion at 1800 rpm drives a 60-tooth gear. The gear speed is:

    • A

      5400 rpm

    • B

      900 rpm

    • C

      3600 rpm

    • 600 rpm

    Speed ratio = 60/20 = 3, so the gear turns at 1800/3 = 600 rpm. 5400 rpm would be a multiplier, not a reducer.

  7. 7

    Standard full-depth 20 degree teeth have an addendum and dedendum of:

    • A

      m and m

    • B

      1.25 m and m

    • m and 1.25 m

    • D

      2.25 m and 1.25 m

    Addendum = m, dedendum = 1.25 m, leaving 0.25 m clearance. The whole depth is 2.25 m.

  8. 8

    Which is the main disadvantage of helical gears compared to spur gears?

    • A

      Louder operation

    • Axial thrust

    • C

      Lower load capacity

    • D

      Cannot be used at high speed

    Angled teeth produce an axial force that thrust bearings must carry. They are quieter and stronger than spur gears.

  9. 9

    In the Goodman diagram shown, what bounds the safe region on the mean-stress axis?

    • Sut on the Goodman line, Sy on the yield line

    • B

      Se on both lines

    • C

      Sy on the Goodman line

    • D

      Sut on the yield line

    Goodman runs to Sut, but the yield line limits the safe region to Sy on that axis. The safe region is enclosed by both lines.

  10. 10

    Which factor increases the fatigue notch factor Kf toward Kt?

    • A

      Low notch sensitivity

    • B

      Larger fillet radius

    • C

      Shot peening

    • High notch sensitivity q approaching 1

    Kf = 1 + q(Kt - 1). When q = 1 the material is fully notch sensitive and Kf = Kt; q = 0 gives Kf = 1.

  11. 11

    A bolt joint has members much stiffer than the bolt. When an external tensile load is applied, the bolt:

    • A

      Carries almost all of it

    • Carries only a small fraction, because the preload in the members is just relieved

    • C

      Carries none

    • D

      Always yields

    The bolt sees C = kb/(kb + km), which is small when members are stiff. This is why preload is so important for fatigue.

  12. 12

    Recommended preload for a reusable bolted connection is about:

    • 75% of proof load

    • B

      50% of proof load

    • C

      25% of proof load

    • D

      100% of yield

    About 75% of proof strength x stress area for reusable joints (about 90% for permanent joints).

  13. 13

    M10 x 1.5 refers to:

    • A

      10 threads per inch

    • B

      Length 10 mm, lead 1.5 mm

    • C

      Diameter 1.5 mm, 10 threads

    • Diameter 10 mm, pitch 1.5 mm

    Metric threads are specified by nominal diameter and pitch (mm).

  14. 14

    A power screw is self-locking if:

    • A

      tan(lead angle) > friction coefficient

    • B

      Lead = pitch

    • friction coefficient > tan(lead angle)

    • D

      It is a ball screw

    With mu > tan(lambda), friction holds the load and it will not back-drive. Ball screws are low-friction and are not self-locking.

  15. 15

    A steel rod (E = 200 GPa), 20 mm diameter, 1 m long and pinned at both ends. Its Euler critical load is closest to:

    • 15.5 kN

    • B

      1.55 kN

    • C

      155 kN

    • D

      1550 kN

    I = pi d^4/64 = 7.85e-9 m^4; Pcr = pi^2 E I / L^2 = 15.5 kN.

  16. 16

    The effective length factor K for a fixed-free (cantilever) column is:

    • A

      0.5

    • 2.0

    • C

      1.0

    • D

      0.7

    Fixed-free columns buckle like half a pinned column, so Le = 2L. Fixed-fixed has K = 0.5.

  17. 17

    A ball bearing with a dynamic load rating C = 20 kN carries an equivalent load of 5 kN. L10 life is:

    • 64 million revs

    • B

      20 million revs

    • C

      4 million revs

    • D

      400 million revs

    L10 = (C/P)^3 = 4^3 = 64 million revolutions. For roller bearings the exponent is 10/3.

  18. 18

    What does L10 mean?

    • A

      The mean life of the bearings

    • B

      The life of 10% of the bearings

    • The life that 90% of identical bearings reach or exceed

    • D

      The life at 10 kN

    L10 is the 10th-percentile life: 10% fail earlier, 90% last at least that long.

  19. 19

    On the Stribeck curve shown, which regime has the lowest friction coefficient?

    • Near the minimum, at the mixed-to-hydrodynamic transition

    • B

      Mixed, well before the minimum

    • C

      Boundary

    • D

      Far right, at very high ZN/P

    Friction is lowest near the transition from mixed to full-film lubrication, then rises gradually with viscous drag as speed increases.

  20. 20

    True or false: A journal bearing runs in the hydrodynamic regime only when a converging wedge forms between journal and bearing.

    • True

    • B

      False

    The eccentric journal drags oil into a converging gap, generating pressure that carries the load. Without motion or viscosity, no film forms.

  21. 21

    A shaft carries 10 kW at 1500 rpm. The torque is about:

    • A

      6.7 N·m

    • B

      1500 N·m

    • C

      637 N·m

    • 63.7 N·m

    omega = 2 pi x 1500/60 = 157 rad/s; T = P/omega = 10,000/157 = 63.7 N·m.

  22. 22

    A 10 mm wide, 40 mm long key transmits a torque of 200 N·m on a 40 mm shaft. Shear stress in the key is:

    • A

      5 MPa

    • 25 MPa

    • C

      250 MPa

    • D

      10 MPa

    F = 2T/d = 2(200)/0.04 = 10 kN; tau = F/(w l) = 10,000/(10 x 40) = 25 MPa.

  23. 23

    Two springs of 10 N/mm and 10 N/mm are connected in series. The combined rate is:

    • A

      20 N/mm

    • B

      10 N/mm

    • 5 N/mm

    • D

      100 N/mm

    1/k = 1/10 + 1/10, so k = 5 N/mm. Parallel would give 20.