Quiz · Hard
Numeric multi-step problems on deflection, Mohr's circle, thermal stress, buckling and fixed-end moments.
A simply supported steel beam (E = 200 GPa, I = 2.0×10⁸ mm⁴) spans 5 m under w = 12 kN/m (12 N/mm). What is its midspan deflection?
About 2.4 mm
About 12 mm
About 0.5 mm
About 24 mm
δ = 5wL⁴/(384EI) = 5(12)(5000⁴)/(384 × 200,000 × 2.0×10⁸) = 3.75×10¹⁶ / 1.536×10¹⁶ ≈ 2.4 mm. A decimal-place slip gives the 24 mm distractor.
A column with a section I = 8×10⁶ mm⁴ and A = 2000 mm² has a radius of gyration of
4000 mm
20 mm
63.2 mm
200 mm
r = √(I/A) = √(8×10⁶/2000) = √4000 = 63.2 mm. 4000 forgets the square root.
A steel bar restrained at both ends warms by 30 °C. E = 200 GPa and α = 12×10⁻⁶ /°C. What compressive stress develops?
7.2 MPa
360 MPa
144 MPa
72 MPa
σ = EαΔT = 200,000 × 12×10⁻⁶ × 30 = 72 MPa. Restraint converts the free thermal strain into stress; the length does not matter.
For σx = 80 MPa, σy = 20 MPa and τxy = 40 MPa, the maximum in-plane shear stress is
40 MPa
50 MPa
30 MPa
100 MPa
Radius of Mohr's circle: √(30² + 40²) = 50 MPa. 100 MPa is the major principal stress, not a shear stress.
A fixed-fixed beam of span 6 m carries w = 12 kN/m. The fixed-end moment is
54 kN·m
72 kN·m
36 kN·m
108 kN·m
wL²/12 = 12 × 36/12 = 36 kN·m. 54 is wL²/8 (simple span midspan moment) and 108 would be wL²/4.
A 200 mm × 400 mm (b × h) rectangular beam carries M = 80 kN·m. What is the maximum bending stress?
15 MPa
30 MPa
7.5 MPa
60 MPa
S = bh²/6 = 200 × 400²/6 = 5.33×10⁶ mm³. σ = M/S = 80×10⁶/5.33×10⁶ = 15 MPa. Swapping b and h would give 30 MPa.
Max shear stress in a rectangular beam section with V = 120 kN, b = 200 mm, h = 300 mm is
3.0 MPa
2.0 MPa
4.0 MPa
1.5 MPa
τmax = 1.5V/A = 1.5 × 120,000/(60,000) = 3.0 MPa. 2.0 MPa is the average V/A, which understates the peak at the neutral axis.
A pipe of radius 500 mm and wall thickness 10 mm carries internal pressure of 2 MPa. The longitudinal stress is
100 MPa
25 MPa
50 MPa
200 MPa
σL = pr/(2t) = 2 × 500/20 = 50 MPa. Hoop stress is 100 MPa.
A pinned-pinned column has Euler load Pcr. If its end conditions are changed to fixed-fixed with the same length, the Euler load becomes
2 Pcr
4 Pcr
Pcr/4
16 Pcr
K drops from 1.0 to 0.5, and Pcr ∝ 1/K², so the load is multiplied by 4.
A tension rod must carry 150 kN with an allowable stress of 150 MPa. The minimum area is
10,000 mm²
100 mm²
2250 mm²
1000 mm²
A = P/σ = 150,000/150 = 1000 mm². Mind the kN to N conversion.
For a cable with sag h = 5 m, span L = 40 m and w = 10 kN/m (per horizontal length), the horizontal tension is
200 kN
800 kN
400 kN
100 kN
H = wL²/(8h) = 10 × 1600/(40) = 400 kN.
A truss joint has three members, two of which are collinear, and no load or support at the joint. The third member is
a zero-force member
in compression
in tension
carrying half the load of the collinear members
With no load, the force component perpendicular to the collinear pair can only be zero, so the third member carries no force.
A beam is subjected to D = 80 kN and L = 100 kN. The LRFD factored load is
180 kN
192 kN
280 kN
256 kN
1.2(80) + 1.6(100) = 96 + 160 = 256 kN. 1.4D = 112 kN is smaller here, so it does not govern.
The tip deflection of a cantilever with end load P is PL³/3EI. If both P and L double, the deflection becomes
8 times larger
16 times larger
4 times larger
2 times larger
Deflection ∝ P·L³ = 2 × 8 = 16.