StudyFox
कीमतेंब्लॉगएक्सटेंशनमुफ़्त टूल
  • कीमतें
  • ब्लॉग
  • एक्सटेंशन
  • मुफ़्त टूल
  • शुरू करेंसाइन इन
StudyFox

अपने नोट्स, PDF और स्लाइड्स को फ़्लैशकार्ड, क्विज़, नोट्स और माइंड मैप में बदलें।

StudyFox खोलें

स्टडी टूल्स

  • होमवर्क हेल्पर
  • नोट मेकर
  • फ़्लैशकार्ड मेकर
  • क्विज़ मेकर
  • माइंड मैप मेकर

प्रोडक्ट

  • कीमतें
  • Chrome एक्सटेंशन
  • मुफ़्त एक्सटेंशन
  • स्टडी सेट देखें
  • ब्लॉग

सहायता

  • सहायता केंद्र
  • संपर्क करें
  • गोपनीयता नीति
  • सेवा की शर्तें

तुलना करें

  • Chegg का विकल्प
  • Course Hero का विकल्प
  • Coursology का विकल्प
  • Photomath का विकल्प
  • Gauthmath का विकल्प
  • PhotoSolve का विकल्प
  • CollegeTools का विकल्प
  • Transcript का विकल्प
  • SmartSolve का विकल्प
  • Homeworkify का विकल्प
  • AnswersAi का विकल्प
  • StudyX का विकल्प
  • Quizlet का विकल्प
  • Anki का विकल्प
  • Knowt का विकल्प
  • Brainscape का विकल्प
  • सभी तुलनाएँ

© 2026 StudyFox AI. सर्वाधिकार सुरक्षित।

  • X
  • Discord
  • Instagram
ExploreEngineering & TechOther EngineeringIndustrial Engineering: Lean, Inventory and Quality Quiz

Quiz · Medium

Industrial Engineering: Lean, Inventory and Quality Quiz

Twenty questions on takt time, EOQ, OEE, learning curves, reliability, capability and queueing.

by Kill h.20 questionsCreated Nov 20, 2026, 08:27 PM
Other Engineering· Industrial EngineeringTags#industrial-engineering#lean#quality#quiz

20 questions

  1. 1

    A cell must produce 480 units in a 480-minute shift with 30 minutes of breaks. What is the takt time?

    • A

      1.0 min

    • B

      0.89 min

    • C

      1.06 min

    • 0.94 min

    Available time = 480 - 30 = 450 min; 450/480 = 0.94 min. Using 480 ignores the breaks (1.0).

  2. 2

    Which is NOT one of the classic seven lean wastes?

    • A

      Overproduction

    • Automation

    • C

      Waiting

    • D

      Defects

    Automation is a tool, not a waste. The others are on the list (overproduction, waiting, defects, plus transport, inventory, motion, over-processing).

  3. 3

    Average WIP is 40 jobs and the plant ships 8 jobs per day. By Little's law the average time in the system is:

    • A

      320 days

    • B

      0.2 days

    • 5 days

    • D

      48 days

    W = L / lambda = 40/8 = 5 days. 0.2 comes from inverting the ratio.

  4. 4

    D = 2,000 units/yr, S = $40/order, H = $4/unit-yr. EOQ is:

    • A

      632

    • B

      80

    • 200

    • D

      400

    Q = sqrt(2*2000*40/4) = sqrt(40000) = 200. 632 comes from forgetting to divide by H.

  5. 5

    At the EOQ:

    • A

      Ordering cost is zero

    • B

      Holding cost is double ordering cost

    • Ordering cost equals holding cost

    • D

      Total cost is zero

    Total cost is minimized where annual ordering cost equals annual holding cost.

  6. 6

    Which scheduling rule minimizes mean flow time on one machine?

    • A

      FCFS

    • SPT

    • C

      Longest processing time

    • D

      EDD

    SPT. EDD minimizes maximum lateness; FCFS has no optimality property.

  7. 7

    A machine: availability 85%, performance 90%, quality 96%. OEE is closest to:

    • 73%

    • B

      77%

    • C

      85%

    • D

      90%

    0.85 x 0.90 x 0.96 = 0.734. Averaging the three (90%) is the common mistake.

  8. 8

    An 80% learning curve: unit 1 takes 50 hours. Unit 4 takes:

    • A

      30 h

    • 32 h

    • C

      40 h

    • D

      20 h

    Two doublings: 50 x 0.8 x 0.8 = 32 hours.

  9. 9

    Three components in series have reliabilities 0.95, 0.90 and 0.98. System reliability is:

    • A

      0.90

    • 0.838

    • C

      0.95

    • D

      0.977

    Series: 0.95 x 0.90 x 0.98 = 0.838. It must be below the weakest component (0.90).

  10. 10

    A process has Cp = 1.8 but Cpk = 0.7. The best conclusion is:

    • The process is off-center

    • B

      The process variation is too large

    • C

      The process is capable and centered

    • D

      The specification is too tight

    Cp ignores centering and is good here, so the large gap to Cpk means the mean is far from the target.

  11. 11

    A control chart point falls above the UCL. This most likely indicates:

    • A

      That the process is capable

    • B

      A bad sample size

    • A special cause

    • D

      Normal random variation

    Points outside 3 sigma limits are rare under common cause variation (about 0.27%), so look for an assignable cause.

  12. 12

    Which tool ranks defect types by frequency to find the vital few?

    • Pareto chart

    • B

      Scatter plot

    • C

      Fishbone diagram

    • D

      Gantt chart

    The Pareto chart. A fishbone organizes possible causes but does not rank frequencies.

  13. 13

    An M/M/1 queue has arrivals 6/h and service rate 8/h. Average time in the system is:

    • A

      15 min

    • 30 min

    • C

      45 min

    • D

      22.5 min

    W = 1/(mu - lambda) = 1/2 h = 30 min. 22.5 min is the time in the queue only (Wq = lambda/(mu(mu-lambda))).

  14. 14

    Assembly tasks total 150 s and cycle time is 50 s. The minimum number of stations is:

    • A

      2

    • B

      4

    • 3

    • D

      5

    150/50 = 3 stations.

  15. 15

    In time study, normal time is:

    • Observed time x rating factor

    • B

      Standard time / rating

    • C

      Observed time x (1 + allowance)

    • D

      Cycle time / takt

    Normal time = observed x rating. Allowances are then added to get standard time.

  16. 16

    Which layout fits low-volume, high-variety production?

    • A

      Assembly line

    • B

      Fixed-position layout

    • Process layout

    • D

      Product layout

    Process (functional) layout groups similar machines and supports variety. Product layouts suit high volume, standard products.

  17. 17

    The bullwhip effect describes:

    • A

      Production halting on a defect

    • Demand variance amplifying upstream in a supply chain

    • C

      Forecast error shrinking with aggregation

    • D

      Queues forming at a bottleneck

    Orders become more variable than sales as you move upstream.

  18. 18

    Fixed cost $30,000; price $80; variable cost $50. Break-even volume:

    • 1,000 units

    • B

      1,600 units

    • C

      375 units

    • D

      600 units

    30000 / (80 - 50) = 1000 units. 375 comes from dividing by the price alone.

  19. 19

    According to the Theory of Constraints, after identifying the constraint you should:

    • A

      Elevate it first

    • B

      Add capacity to non-constraints

    • C

      Remove all buffers

    • Exploit it

    Step 2 is to exploit the constraint (get the most from it); elevating comes later.

  20. 20

    True or false: Cpk can be larger than Cp.

    • A

      True

    • False

    Cpk = Cp x (1 - k) where k measures off-centering, so Cpk <= Cp, with equality only when centered.