StudyFox
कीमतेंब्लॉगएक्सटेंशनमुफ़्त टूल
  • कीमतें
  • ब्लॉग
  • एक्सटेंशन
  • मुफ़्त टूल
  • शुरू करेंसाइन इन
StudyFox

अपने नोट्स, PDF और स्लाइड्स को फ़्लैशकार्ड, क्विज़, नोट्स और माइंड मैप में बदलें।

StudyFox खोलें

स्टडी टूल्स

  • होमवर्क हेल्पर
  • नोट मेकर
  • फ़्लैशकार्ड मेकर
  • क्विज़ मेकर
  • माइंड मैप मेकर

प्रोडक्ट

  • कीमतें
  • Chrome एक्सटेंशन
  • मुफ़्त एक्सटेंशन
  • स्टडी सेट देखें
  • ब्लॉग

सहायता

  • सहायता केंद्र
  • संपर्क करें
  • गोपनीयता नीति
  • सेवा की शर्तें

तुलना करें

  • Chegg का विकल्प
  • Course Hero का विकल्प
  • Coursology का विकल्प
  • Photomath का विकल्प
  • Gauthmath का विकल्प
  • PhotoSolve का विकल्प
  • CollegeTools का विकल्प
  • Transcript का विकल्प
  • SmartSolve का विकल्प
  • Homeworkify का विकल्प
  • AnswersAi का विकल्प
  • StudyX का विकल्प
  • Quizlet का विकल्प
  • Anki का विकल्प
  • Knowt का विकल्प
  • Brainscape का विकल्प
  • सभी तुलनाएँ

© 2026 StudyFox AI. सर्वाधिकार सुरक्षित।

  • X
  • Discord
  • Instagram
ExploreEngineering & TechCivil EngineeringStructural Analysis Fundamentals: Supports, Beams and Materials

Quiz · Medium

Structural Analysis Fundamentals: Supports, Beams and Materials

Supports, shear and moment diagrams, stress and strain, buckling and the basics of concrete and LRFD.

by Kill h.23 questionsCreated Nov 20, 2026, 08:27 PM
Civil Engineering· StructuresTags#structures#beams#statics

23 questions

  1. 1

    A roller support provides how many reaction components in a plane?

    • A

      Two: horizontal and vertical

    • B

      Three: horizontal, vertical and moment

    • One, perpendicular to the supporting surface

    • D

      One, along the supporting surface

    A roller can only push or pull perpendicular to its surface. It cannot resist sliding along the surface (so not 'along'), and it provides no moment.

  2. 2

    Which condition describes a stable, statically determinate plane truss?

    • m + r = 2j

    • B

      m + r = j

    • C

      m + r = 3j

    • D

      m = 2j + r

    m members plus r reaction components must equal two equilibrium equations per joint (2j). More unknowns than 2j is indeterminate; fewer is unstable.

  3. 3

    Using the diagram, what is the maximum bending moment for the simply supported beam with a central load P?

    • A

      PL/2

    • B

      PL/8

    • C

      P/2

    • PL/4

    Each reaction is P/2, so M at midspan = (P/2)(L/2) = PL/4. PL/8 is the fixed-end moment, not the midspan moment of this beam.

  4. 4

    Where does the maximum bending moment in a beam occur?

    • A

      Always at midspan

    • Where the shear force is zero or changes sign

    • C

      Always at the supports

    • D

      Where the load is largest

    dM/dx = V, so M has a peak where V = 0. It is at midspan only for symmetric loading.

  5. 5

    A cantilever of length 4 m carries a uniform load of 5 kN/m. The maximum moment is

    • A

      20 kN·m at the fixed end

    • 40 kN·m at the fixed end

    • C

      40 kN·m at the free end

    • D

      10 kN·m at midspan

    M = wL²/2 = 5(16)/2 = 40 kN·m at the support. 20 kN is the maximum shear (wL), not a moment.

  6. 6

    A simply supported beam has L = 6 m and w = 10 kN/m. What is the maximum bending moment?

    • A

      30 kN·m

    • B

      60 kN·m

    • C

      90 kN·m

    • 45 kN·m

    wL²/8 = 10(36)/8 = 45 kN·m. 30 kN is the reaction wL/2, and 90 would come from wL²/4.

  7. 7

    In the flexure formula σ = My/I, y is

    • the distance from the neutral axis to the point

    • B

      the beam deflection

    • C

      the distance from the top of the section

    • D

      the yield strength

    Stress varies linearly from zero at the neutral axis to a maximum at the extreme fiber.

  8. 8

    Doubling the depth of a rectangular beam (same width) increases its bending strength (section modulus) by a factor of

    • A

      2

    • B

      6

    • 4

    • D

      8

    S = bh²/6, so doubling h gives four times S. A factor of 8 applies to the moment of inertia I, which controls deflection.

  9. 9

    Which point on a ductile steel stress-strain curve marks the highest engineering stress?

    • A

      Yield point

    • B

      Proportional limit

    • C

      Fracture

    • Ultimate strength

    After the ultimate strength, necking reduces the area and engineering stress falls, so fracture occurs at a lower stress.

  10. 10

    A 100 kN tension force acts on a bar with A = 500 mm², L = 2 m and E = 200 GPa. The elongation is

    • A

      0.2 mm

    • 2 mm

    • C

      20 mm

    • D

      1 mm

    δ = PL/AE = (100,000 × 2000)/(500 × 200,000) = 2 mm. Watch units: use N, mm and MPa consistently.

  11. 11

    Euler's formula for the critical load of a column depends on

    • A

      Yield strength and area

    • B

      Compressive strength of the material only

    • E, I, length and end conditions

    • D

      Cross-sectional area and length only

    P_cr = π²EI/(KL)². Yield strength does not appear, which is why Euler only applies to slender columns.

  12. 12

    The theoretical effective length factor K for a fixed-free (flagpole) column is

    • 2.0

    • B

      0.5

    • C

      0.7

    • D

      1.0

    A free end doubles the effective length. 0.5 is fixed-fixed, 0.7 fixed-pinned and 1.0 pinned-pinned.

  13. 13

    Which change reduces a column's buckling load the most?

    • Doubling its length

    • B

      Doubling its yield strength

    • C

      Increasing its cross-section area by 10%

    • D

      Using a stiffer end support

    P_cr is proportional to 1/L², so doubling the length cuts the load to one quarter. Yield strength is not in Euler's formula.

  14. 14

    Hoop stress in a thin-walled pressurized cylinder compared with longitudinal stress is

    • A

      equal

    • B

      half as large

    • twice as large

    • D

      four times as large

    Hoop σ = pr/t and longitudinal σ = pr/(2t), so cylinders split along their length first.

  15. 15

    Concrete is reinforced with steel mainly because

    • A

      concrete is weak in compression

    • concrete is weak in tension

    • C

      steel reduces concrete's weight

    • D

      steel prevents shrinkage entirely

    Concrete's tensile strength is roughly a tenth of its compressive strength. Reinforcement carries tension; it does not eliminate shrinkage.

  16. 16

    An under-reinforced concrete beam is preferred because it

    • A

      has the highest possible strength

    • B

      never cracks

    • C

      fails suddenly by concrete crushing

    • fails in a ductile way, with steel yielding first

    Steel yield gives large deflections and cracks as a warning. Over-reinforced beams crush in a brittle way.

  17. 17

    In LRFD, which gravity load combination is commonly used?

    • A

      1.0D + 1.0L

    • B

      1.6D + 1.2L

    • 1.2D + 1.6L

    • D

      1.4L only

    Live load carries the larger factor because it is less predictable than dead load.

  18. 18

    Fixed-end moment for a fixed-fixed beam with a uniform load w over span L is

    • wL²/12

    • B

      wL²/8

    • C

      wL²/2

    • D

      PL/8

    wL²/8 is the simply supported midspan moment; wL²/2 is the cantilever moment; PL/8 is for a central point load.

  19. 19

    A pin support can resist an applied moment.

    • A

      True

    • False

    A pin allows rotation, so it provides only horizontal and vertical force reactions.

  20. 20

    A statically indeterminate structure cannot be solved without considering deformations.

    • True

    • B

      False

    Statics provides too few equations, so compatibility conditions (deformation, material stiffness) are needed.

  21. 21

    In a simply supported beam under gravity load, which fibers are in tension at midspan?

    • A

      The top fibers

    • B

      The neutral axis

    • C

      Both top and bottom equally

    • The bottom fibers

    Sagging bending compresses the top and stretches the bottom, which is why main reinforcement goes near the bottom.

  22. 22

    The Müller-Breslau principle is used to

    • A

      compute buckling loads

    • sketch influence lines

    • C

      design prestressed beams

    • D

      find principal stresses

    The influence line for a response has the shape of the deflected structure after releasing the corresponding restraint and applying a unit displacement.

  23. 23

    Which relationship is correct for a beam with distributed load w(x)?

    • A

      dM/dx = −w and dV/dx = V

    • dV/dx = −w and dM/dx = V

    • C

      dV/dx = M and dM/dx = w

    • D

      dV/dx = w and dM/dx = −V

    Shear changes by the (negative) load, and moment changes by the shear. Differentiating twice gives d²M/dx² = −w.