StudyFox
कीमतेंब्लॉगएक्सटेंशनमुफ़्त टूल
  • कीमतें
  • ब्लॉग
  • एक्सटेंशन
  • मुफ़्त टूल
  • शुरू करेंसाइन इन
StudyFox

अपने नोट्स, PDF और स्लाइड्स को फ़्लैशकार्ड, क्विज़, नोट्स और माइंड मैप में बदलें।

StudyFox खोलें

स्टडी टूल्स

  • होमवर्क हेल्पर
  • नोट मेकर
  • फ़्लैशकार्ड मेकर
  • क्विज़ मेकर
  • माइंड मैप मेकर

प्रोडक्ट

  • कीमतें
  • Chrome एक्सटेंशन
  • मुफ़्त एक्सटेंशन
  • स्टडी सेट देखें
  • ब्लॉग

सहायता

  • सहायता केंद्र
  • संपर्क करें
  • गोपनीयता नीति
  • सेवा की शर्तें

तुलना करें

  • Chegg का विकल्प
  • Course Hero का विकल्प
  • Coursology का विकल्प
  • Photomath का विकल्प
  • Gauthmath का विकल्प
  • PhotoSolve का विकल्प
  • CollegeTools का विकल्प
  • Transcript का विकल्प
  • SmartSolve का विकल्प
  • Homeworkify का विकल्प
  • AnswersAi का विकल्प
  • StudyX का विकल्प
  • Quizlet का विकल्प
  • Anki का विकल्प
  • Knowt का विकल्प
  • Brainscape का विकल्प
  • सभी तुलनाएँ

© 2026 StudyFox AI. सर्वाधिकार सुरक्षित।

  • X
  • Discord
  • Instagram
ExploreEngineering & TechOther EngineeringEngineering Drawing: Views, Dimensions and Tolerances Quiz

Quiz · Medium

Engineering Drawing: Views, Dimensions and Tolerances Quiz

Twenty questions on projection, line types, sections, dimensioning, fits and GD&T.

by Kill h.20 questionsCreated Nov 20, 2026, 08:27 PM
Other Engineering· Engineering DrawingTags#engineering-drawing#tolerances#gd-and-t#quiz

20 questions

  1. 1

    Which control does not require a datum?

    • Cylindricity

    • B

      Perpendicularity

    • C

      Position

    • D

      Total runout

    Cylindricity is a form control. The others are referenced to datums.

  2. 2

    In third-angle projection, the top view is placed:

    • Above the front view

    • B

      Behind the front view

    • C

      To the left of the front view

    • D

      Below the front view

    Third angle (US): top above, right to the right. Below the front view is first angle.

  3. 3

    Which line type shows the path of the viewing plane for a section?

    • Cutting-plane line

    • B

      Center line

    • C

      Phantom line

    • D

      Hidden line

    A thick cutting-plane line with arrows shows where the part is cut and the viewing direction.

  4. 4

    Hidden lines are drawn:

    • A

      As long-short-long dashes

    • B

      As thick continuous lines

    • As short dashes

    • D

      As thin continuous lines

    Hidden lines are medium-weight dashes. Long-short-long is a center line.

  5. 5

    Which scale is an enlargement?

    • A

      1:1

    • B

      1:10

    • 2:1

    • D

      1:2

    2:1 means the drawing is twice actual size.

  6. 6

    An inclined surface appears in true size in which view?

    • A

      The top view

    • B

      The front view

    • An auxiliary view

    • D

      The section view

    Only a view projected perpendicular to the edge view of the surface shows true shape.

  7. 7

    The hatching in a section view is normally drawn at:

    • A

      30 degrees on the horizontal only

    • 45 degrees

    • C

      Random angles

    • D

      90 degrees

    Thin 45 degree lines; parts adjacent in an assembly use opposite directions.

  8. 8

    Hole limits 20.000 to 20.021; shaft limits 19.980 to 19.993. This is:

    • A clearance fit

    • B

      An interference fit

    • C

      A press fit

    • D

      A transition fit

    Max shaft (19.993) is less than min hole (20.000), so there is always clearance (min 0.007).

  9. 9

    Hole 30.000 to 30.021; shaft 30.015 to 30.028. This fit is:

    • A

      Press

    • Transition

    • C

      Clearance

    • D

      Interference

    Smallest hole (30.000) is less than the largest shaft (30.028) and the largest hole (30.021) is more than the smallest shaft (30.015), so both clearance and interference are possible: a transition fit.

  10. 10

    What does the GD&T characteristic flatness control?

    • A

      Orientation to a datum

    • Form of a surface

    • C

      Surface roughness

    • D

      Location of a hole

    Flatness is a form control with no datum; it constrains the surface between two parallel planes.

  11. 11

    In a feature control frame, the first datum letter is the:

    • Primary datum

    • B

      Tertiary datum

    • C

      Diameter symbol

    • D

      Material condition

    Datums are listed in order of precedence: primary, secondary, tertiary.

  12. 12

    The isometric axes make which angle with the horizontal?

    • A

      15 degrees

    • B

      60 degrees

    • 30 degrees

    • D

      45 degrees

    Isometric axes are drawn 30 degrees from horizontal and 120 degrees apart.

  13. 13

    Which dimension rule is correct?

    • Give each dimension once, outside the view where possible

    • B

      Dimension to hidden lines

    • C

      Repeat dimensions in every view for safety

    • D

      Dimension to center lines of the object edges

    Duplicate dimensions risk conflicts when revised. Dimensioning to hidden lines is avoided.

  14. 14

    What is the standard countersink angle for metric screws?

    • A

      120 degrees

    • 90 degrees

    • C

      60 degrees

    • D

      82 degrees

    Metric countersinks are 90 degrees; 82 degrees is the inch standard.

  15. 15

    M12 x 1.75 designates:

    • A

      12 threads per inch

    • B

      1.75 mm diameter

    • Metric thread of 12 mm diameter, 1.75 mm pitch

    • D

      A tolerance class

    The second number is pitch in mm, not threads per inch.

  16. 16

    Bonus tolerance applies when a position tolerance is specified at:

    • A

      LMC only

    • B

      Basic size

    • MMC

    • D

      RFS

    At MMC, the feature's departure from MMC increases the available position tolerance.

  17. 17

    Which is a purpose of an exploded assembly view?

    • A

      Give tolerances

    • Show how parts fit together

    • C

      Hide internal features

    • D

      Show the material

    Parts are separated along their assembly axes.

  18. 18

    True or false: In first-angle projection the right-side view is to the right of the front view.

    • A

      True

    • False

    In first angle the right-side view is on the left; third angle puts it on the right.

  19. 19

    Worst-case stack-up of four parts each 25.0 +/- 0.05 gives a total tolerance of:

    • A

      +/- 0.10

    • B

      +/- 0.05

    • C

      +/- 0.40

    • +/- 0.20

    Worst-case adds: 4 x 0.05 = 0.20. The RSS (statistical) value would be 0.10.

  20. 20

    A scale of 1:5 means the drawing is:

    • One fifth of actual size

    • B

      The same as actual size

    • C

      Five times actual size

    • D

      One fifth of the paper size

    1:5 is a reduction; the dimension values still show the true size.