Quiz · Hard
Numeric problems on phase relations, consolidation, earth pressure, slopes and piles.
A soil has Gs = 2.70, e = 0.65 and is saturated. What is its water content?
17.3%
65%
24.1%
38%
w = Se/Gs = 0.65/2.70 = 0.241.
Gs = 2.65 and e = 0.60. Dry unit weight is closest to
16.3 kN/m³
20.6 kN/m³
26.0 kN/m³
10.2 kN/m³
γd = Gs γw/(1 + e) = 2.65(9.81)/1.6 = 16.25 kN/m³.
Emax = 0.90, emin = 0.40, e = 0.55. The relative density and classification are
70%, dense
30%, loose
70%, very dense
35%, medium
Dr = (0.90 − 0.55)/(0.90 − 0.40) = 0.70, in the 65 to 85% dense range.
A 4 m thick NC clay layer: Cc = 0.30, e0 = 0.90, σ'0 = 100 kPa, Δσ = 50 kPa. Primary consolidation settlement is closest to
64 mm
222 mm
111 mm
0.5 m
Sc = (0.3 × 4/1.9) log(150/100) = 0.632 × 0.176 = 0.111 m.
A 4 m clay layer drains at top and bottom (cv = 2×10⁻⁷ m²/s). Time for 50% consolidation (T = 0.197)?
about 92 days
about 46 days
about 184 days
about 12 days
Hdr = 2 m; t = 0.197 × 4/2×10⁻⁷ = 3.94×10⁶ s ≈ 45.6 days. Using Hdr = 4 m would give 4 times longer.
Seepage under a dam: H = 6 m, k = 1×10⁻⁵ m/s, Nf = 4, Nd = 10. Flow per meter of dam is
6×10⁻⁵ m³/s
1.5×10⁻⁴ m³/s
2.4×10⁻⁶ m³/s
2.4×10⁻⁵ m³/s
q = kH Nf/Nd = 10⁻⁵ × 6 × 0.4.
A sand (c = 0, φ = 30°) has σ3 = 100 kPa at failure. σ1 is
200 kPa
173 kPa
300 kPa
130 kPa
σ1 = σ3 tan²(60°) = 3σ3.
A 6 m high smooth wall retains dry sand (γ = 18 kN/m³, φ = 30°). Active thrust per meter and its location are
108 kN/m at 2 m above the base
324 kN/m at 2 m above the base
108 kN/m at 3 m above the base
54 kN/m at 2 m above the base
Pa = ½(1/3)(18)(36) = 108 kN/m, acting at H/3. Using Kp gives 324 kN/m.
A strip footing on clay (cu = 50 kPa) at the surface with FS = 3 and Nc = 5.14 has allowable bearing pressure of
257 kPa
50 kPa
17 kPa
86 kPa
qult = 5.14(50) = 257 kPa. Divide by 3 = 85.7 kPa.
Pile end bearing in clay with cu = 80 kPa and diameter 0.4 m is closest to
720 kN
90 kN
36 kN
25 kN
Qp = 9 cu Ap = 9 × 80 × 0.1257 = 90.5 kN. 720 forgets the area.
An infinite dry sand slope with φ = 32° is inclined at 20°. The factor of safety is
0.58
1.72
1.60
2.5
FS = tan32°/tan20° = 0.625/0.364.
A fill has field γd = 17.6 kN/m³ and lab maximum γd = 18.5 kN/m³. If the specification requires 95% relative compaction, the fill
fails (RC = 90%)
fails (RC = 105%)
cannot be judged without moisture
just passes (RC = 95.1%)
RC = 17.6/18.5 = 0.951. Moisture only matters as it affects density, which is already measured.