Quiz · Medium
Twenty questions on projection, line types, sections, dimensioning, fits and GD&T.
Which control does not require a datum?
Cylindricity
Perpendicularity
Position
Total runout
Cylindricity is a form control. The others are referenced to datums.
In third-angle projection, the top view is placed:
Above the front view
Behind the front view
To the left of the front view
Below the front view
Third angle (US): top above, right to the right. Below the front view is first angle.
Which line type shows the path of the viewing plane for a section?
Cutting-plane line
Center line
Phantom line
Hidden line
A thick cutting-plane line with arrows shows where the part is cut and the viewing direction.
Hidden lines are drawn:
As long-short-long dashes
As thick continuous lines
As short dashes
As thin continuous lines
Hidden lines are medium-weight dashes. Long-short-long is a center line.
Which scale is an enlargement?
1:1
1:10
2:1
1:2
2:1 means the drawing is twice actual size.
An inclined surface appears in true size in which view?
The top view
The front view
An auxiliary view
The section view
Only a view projected perpendicular to the edge view of the surface shows true shape.
The hatching in a section view is normally drawn at:
30 degrees on the horizontal only
45 degrees
Random angles
90 degrees
Thin 45 degree lines; parts adjacent in an assembly use opposite directions.
Hole limits 20.000 to 20.021; shaft limits 19.980 to 19.993. This is:
A clearance fit
An interference fit
A press fit
A transition fit
Max shaft (19.993) is less than min hole (20.000), so there is always clearance (min 0.007).
Hole 30.000 to 30.021; shaft 30.015 to 30.028. This fit is:
Press
Transition
Clearance
Interference
Smallest hole (30.000) is less than the largest shaft (30.028) and the largest hole (30.021) is more than the smallest shaft (30.015), so both clearance and interference are possible: a transition fit.
What does the GD&T characteristic flatness control?
Orientation to a datum
Form of a surface
Surface roughness
Location of a hole
Flatness is a form control with no datum; it constrains the surface between two parallel planes.
In a feature control frame, the first datum letter is the:
Primary datum
Tertiary datum
Diameter symbol
Material condition
Datums are listed in order of precedence: primary, secondary, tertiary.
The isometric axes make which angle with the horizontal?
15 degrees
60 degrees
30 degrees
45 degrees
Isometric axes are drawn 30 degrees from horizontal and 120 degrees apart.
Which dimension rule is correct?
Give each dimension once, outside the view where possible
Dimension to hidden lines
Repeat dimensions in every view for safety
Dimension to center lines of the object edges
Duplicate dimensions risk conflicts when revised. Dimensioning to hidden lines is avoided.
What is the standard countersink angle for metric screws?
120 degrees
90 degrees
60 degrees
82 degrees
Metric countersinks are 90 degrees; 82 degrees is the inch standard.
M12 x 1.75 designates:
12 threads per inch
1.75 mm diameter
Metric thread of 12 mm diameter, 1.75 mm pitch
A tolerance class
The second number is pitch in mm, not threads per inch.
Bonus tolerance applies when a position tolerance is specified at:
LMC only
Basic size
MMC
RFS
At MMC, the feature's departure from MMC increases the available position tolerance.
Which is a purpose of an exploded assembly view?
Give tolerances
Show how parts fit together
Hide internal features
Show the material
Parts are separated along their assembly axes.
True or false: In first-angle projection the right-side view is to the right of the front view.
True
False
In first angle the right-side view is on the left; third angle puts it on the right.
Worst-case stack-up of four parts each 25.0 +/- 0.05 gives a total tolerance of:
+/- 0.10
+/- 0.05
+/- 0.40
+/- 0.20
Worst-case adds: 4 x 0.05 = 0.20. The RSS (statistical) value would be 0.10.
A scale of 1:5 means the drawing is:
One fifth of actual size
The same as actual size
Five times actual size
One fifth of the paper size
1:5 is a reduction; the dimension values still show the true size.