Quiz · Hard
Applied multi-step problems on fluxes, overall coefficients, minimum stages, absorbers and osmotic pressure.
Equimolar counterdiffusion of A and B in an ideal gas at 300 K. p_A1 = 20 kPa, p_A2 = 5 kPa, gap 2 mm, D_AB = 1.5e-5 m²/s. The flux of A is closest to:
0.0045 mol/m²/s
0.045 mol/m²/s
4.5 mol/m²/s
0.45 mol/m²/s
N = D Δp /(R T Δz) = 1.5e-5 x 15000 / (8.314 x 300 x 0.002) = 0.0451 mol/m²/s. Watch the units: kPa must be converted to Pa.
For a stagnant-film calculation with P = 100 kPa and p_B1 = 80 kPa, p_B2 = 95 kPa, the log-mean p_B,lm is closest to:
85 kPa
90 kPa
87.3 kPa
87.5 kPa, the arithmetic mean
p_B,lm = (95 - 80)/ln(95/80) = 87.3 kPa. The arithmetic mean (87.5) is close but is not what the formula gives.
1/K_y = 1/k_y + m/k_x with k_y = 0.02, k_x = 0.05 mol/m²/s and m = 0.5. What fraction of the resistance is in the gas film?
50%
83%
100%
17%
1/k_y = 50, m/k_x = 10, total 60 m²s/mol. Gas fraction = 50/60 = 83%. Many forget to multiply 1/k_x by m.
Sh = 2 + 0.6 Re^0.5 Sc^(1/3) for a sphere with Re = 10^4 and Sc = 1000. Sh is:
About 6002
About 62
About 202
About 602
Re^0.5 = 100, Sc^(1/3) = 10, so Sh = 2 + 0.6 x 100 x 10 = 602.
A gas diffuses in a porous solid with D_AB = 2.0e-5 m²/s, porosity 0.4 and tortuosity 2. The effective diffusivity is:
1.6e-5 m²/s
4.0e-6 m²/s
8.0e-6 m²/s
2.0e-5 m²/s
D_eff = D ε / τ = 2.0e-5 x 0.4 / 2 = 4.0e-6 m²/s. The factor ε/τ is always less than 1.
If the diffusivity in Higbie's penetration model increases fourfold at the same contact time, k_L:
Increases 16-fold
Is unchanged
Increases fourfold
Doubles
k_L is proportional to sqrt(D), and sqrt(4) = 2.
A binary mixture has relative volatility 2.0. A column delivers x_D = 0.95 and x_B = 0.05. The minimum number of stages at total reflux (Fenske) is closest to:
17
4.2
8.5
2.9
N_min = ln[(0.95/0.05)(0.95/0.05)]/ln 2 = ln 361 / 0.693 = 8.5 stages including the reboiler.
R = 3 and x_D = 0.92. What is the rectifying operating line?
y = 0.75x + 0.92
y = 3x + 0.23
y = 0.75x + 0.23
y = 0.25x + 0.23
Slope R/(R+1) = 0.75; intercept x_D/(R+1) = 0.92/4 = 0.23. Check that at x = 0.92 y = 0.69 + 0.23 = 0.92, on the diagonal.
The feed is 40% vaporized (q = 0.6). The q-line slope is:
-1.5
0.6
-0.6
1.5
slope = q/(q-1) = 0.6/(-0.4) = -1.5, negative because the feed is partly vapor.
A Kremser absorber has A = 1.5 and N = 3 ideal stages with x_in = 0. The fraction absorbed is closest to:
99%
88%
67%
77%
(A^4 - A)/(A^4 - 1) = (5.06 - 1.5)/(5.06 - 1) = 0.877, about 88%.
A gas contains 2 mol% solute (m = 1.5) and 90% must be removed with solute-free solvent. L_min/G is closest to:
1.35
2.0
0.67
0.9
y_out = 0.002. At minimum, exit liquid is in equilibrium with inlet gas: x_out* = 0.02/1.5 = 0.01333. L/G_min = (0.02 - 0.002)/0.01333 = 1.35.
A packed absorber needs N_OG = 5 with H_OG = 0.6 m. What packed height is needed?
8.3 m
5.6 m
0.12 m
3.0 m
Z = H_OG x N_OG = 0.6 x 5 = 3.0 m.
12 ideal stages are needed and the overall efficiency is 60%. How many actual trays?
20
15
7
12
N_actual = N_ideal/E_o = 12/0.6 = 20. Multiplying by 0.6 would be wrong because efficiency below 1 means more real trays.
Reverse osmosis of a 0.5 M NaCl solution at 25°C (i = 2). The osmotic pressure is closest to:
1 bar
12 bar
50 bar
25 bar
π = i M R T = 2 x 0.5 mol/L x 0.08314 L·bar/(mol·K) x 298 K = 24.8 bar. The applied pressure must exceed this.
Which change to a separation process will most increase the mass-transfer rate if the process is liquid-film controlled?
Lower the gas temperature
Increase gas velocity
Increase liquid turbulence
Increase the gas packing height only
The liquid film resistance dominates, so only improving k_L (liquid-side mixing) significantly raises K_x. Gas velocity cannot help appreciably.