Quiz · Medium
Twenty questions on crystal structures, stress-strain, strengthening, phase diagrams and steels.
How many atoms belong to one FCC unit cell?
4
8
6
2
FCC: 8 corners x 1/8 + 6 faces x 1/2 = 4. BCC has 2.
Atomic packing factor of FCC is:
0.74
0.91
0.68
0.52
FCC and ideal HCP are the most densely packed (0.74); BCC is 0.68 and simple cubic 0.52.
Which statement about dislocations is correct?
Screw dislocations have Burgers vector perpendicular to the line
Dislocations increase with annealing
Plastic deformation in metals occurs by dislocation motion
Dislocations are point defects
Slip by dislocation glide explains low yield strength. Screw dislocations have b parallel to the line, and dislocations are line defects.
A 20 mm diameter bar carries 60 kN. The engineering stress is closest to:
95 MPa
764 MPa
191 MPa
3 MPa
A = pi(10 mm)^2 = 314.2 mm^2; 60000 N/314.2 mm^2 = 191 MPa. Using the diameter as the radius gives 48 MPa.
A 1 m steel wire (E = 200 GPa) carries 100 MPa. How much does it stretch?
0.05 mm
5 mm
0.5 mm
2 mm
strain = 100/200000 = 5e-4, so elongation = 0.5 mm.
The 0.2% offset method is used to find:
Young's modulus
Yield strength
Fracture strength
Tensile strength
It defines yield strength where the stress-strain curve has no distinct yield point.
Which change makes a metal stronger but less ductile?
Cold working
Recrystallization
Grain growth
Annealing
Cold work multiplies dislocations. Annealing, recrystallization and grain growth all soften the metal.
Hall-Petch says yield strength increases when:
Dislocation density decreases
Grain size decreases
Grain size increases
Temperature increases
Smaller grains mean more boundaries that block dislocations.
The eutectoid reaction in plain carbon steel produces:
Ledeburite
Pearlite
Austenite
Martensite
Austenite at 0.76 wt% C transforms to ferrite + cementite lamellae (pearlite) at 727 C. Ledeburite is the eutectic product in cast iron.
Which cooling of austenite produces martensite?
Rapid quench
Slow furnace cooling
Holding at 700 C
Air cooling
Fast cooling suppresses carbon diffusion, giving diffusionless BCT martensite.
A tie line spans alpha at 10 wt% B and beta at 50 wt% B. For an alloy at 30 wt% B, the fraction of beta is:
0.3
0.75
0.5
0.25
(30 - 10)/(50 - 10) = 0.5.
Which material has an endurance limit?
Low-carbon steel
Copper
Aluminum alloy
Magnesium
Steels show a fatigue limit; most nonferrous alloys do not.
Creep is most significant when temperature exceeds roughly:
Tm/10 only for polymers
0.4 Tm
0.05 Tm
0.1 Tm
Creep becomes important above about 0.4 of the absolute melting temperature.
Thermoset polymers differ from thermoplastics because they:
Are always crystalline
Have no covalent bonds
Are crosslinked and do not remelt
Soften every time they are heated
Crosslinking gives a rigid network that decomposes rather than melts.
True or false: Engineering stress above the UTS falls because the metal is weakening.
True
False
The metal keeps work hardening; the drop is because engineering stress uses the original area while the neck shrinks.
Composite: fibers E = 70 GPa at 50% volume in a matrix with E = 4 GPa. Modulus along the fibers (rule of mixtures):
18 GPa
7.6 GPa
37 GPa
74 GPa
0.5 x 70 + 0.5 x 4 = 37 GPa. 7.6 GPa is the lower bound (transverse).
Zinc is connected to steel in seawater. What happens?
The steel corrodes
The zinc corrodes
Neither corrodes
Both corrode equally
Zinc is more active (anodic), so it is sacrificed to protect the steel.
Which test measures impact energy of a notched bar?
Charpy
Rockwell
Brinell
Vickers
Charpy (or Izod). The others measure hardness.
Which of these is NOT a strengthening mechanism of metals?
Strain hardening
Solid-solution strengthening
Precipitation hardening
Increasing grain size
Larger grains lower strength by Hall-Petch.
Maximum solubility of carbon in austenite is about:
2.14 wt%
6.7 wt%
0.022 wt%
0.76 wt%
2.14 wt% at 1147 C. 0.022% is ferrite, 6.7% is cementite, and 0.76% is the eutectoid composition.