Quiz · Hard
Applied problems on gain-bandwidth, slew rate, 555 timers, rectifier ripple, buck converters and loading effects.
An op-amp has a gain-bandwidth product of 2 MHz. In a non-inverting amplifier with gain 40, the -3 dB bandwidth is about
2 MHz
80 kHz
500 kHz
50 kHz
BW = GBW / gain = 2 MHz / 40 = 50 kHz.
An op-amp's slew rate is 0.5 V/μs. What is the highest frequency at which an undistorted 10 V peak sine wave can be output?
About 7.96 kHz
About 50 kHz
About 796 kHz
About 79.6 kHz
kHz. Check the unit: 0.5 V/μs = 5×10^5 V/s.
A 555 timer in astable mode has kΩ, kΩ and μF. The frequency is about
1.44 kHz
686 Hz
145 Hz
6.9 kHz
Hz.
For the same 555 circuit ( kΩ, kΩ) what is the duty cycle?
About 48%
About 91%
About 52%
50% exactly
. An astable 555 duty cycle is always above 50%.
A BJT biased at mA drives a collector load of kΩ ( mV). The mid-band gain of a common-emitter stage (no emitter resistor, ignoring r_o and loading) is about
-100
-40
+400
-400
mS, . The negative sign reflects inversion.
A zener ( V) regulates from V with a series resistor. Load current is 20 mA and the minimum Zener current should be 5 mA. The largest allowed series resistor is about
276 Ω
345 Ω
690 Ω
138 Ω
. Using only the load current (20 mA) would give 345 Ω, leaving no Zener current.
A full-wave bridge rectifier fed by a 12 V peak transformer secondary and loaded by 100 Ω has an output peak of about
12 V
10.6 V
11.3 V
6 V
Two diodes conduct at a time, dropping about 1.4 V: 12 - 1.4 = 10.6 V. 11.3 V uses only one diode drop.
A filter capacitor of 1000 μF supplies 100 mA to a full-wave rectified 60 Hz supply. The ripple is about
1.67 V
0.17 V
0.83 V
8.3 V
V. A half-wave rectifier would give 1.67 V.
For a buck converter with V producing 5 V (ideal, continuous mode), the duty cycle is
about 0.58
about 2.4
about 0.71
about 0.42
Vout = D Vin, so D = 5/12 = 0.417. For a boost converter the relation would be Vout = Vin/(1-D).
An NMOS has V_th = 1 V. With V_GS = 3 V, in which region is it when V_DS = 1 V?
Triode
Saturation
Cutoff
Breakdown
The saturation boundary is V_GS - V_th = 2 V. V_DS = 1 V is below that, so the channel is not pinched off: triode.
An 8-bit ADC with a 3.3 V reference measures an input. The code is 128. The input voltage is about
0.41 V
1.65 V
3.3 V
0.83 V
V (about half scale). One LSB is 12.9 mV.
An inverting amplifier with kΩ, kΩ has an input source with series resistance . The actual gain is about
-10
-40
-8
-10.5
The source resistance adds to : . This is a common loading trap for inverting amplifiers.
A Schmitt trigger is used instead of a plain comparator mainly to
increase the voltage gain
reduce power consumption
convert current to voltage
avoid output chatter from noise on a slowly changing input
Hysteresis from positive feedback gives separate rising and falling thresholds, so small noise cannot toggle the output repeatedly.
A 2nd-order Butterworth low-pass filter attenuates by about how much one decade above the cutoff?
About 40 dB
About 20 dB
About 60 dB
About 3 dB
Roll-off is 20n dB/decade; n = 2 gives 40 dB/decade (the first -3 dB is at the cutoff itself).