Quiz · Hard
Applied calculations: reactions, moments, stress, buckling, load factors and U-value heat loss.
A simply supported beam spans 6 m and carries a uniform load of 10 kN/m. What is each support reaction?
60 kN
30 kN
15 kN
10 kN
Total load = 10 x 6 = 60 kN, split equally between two supports: 30 kN each. 60 kN is the total, not the reaction.
For the same beam (6 m, 10 kN/m), what is the maximum bending moment?
180 kN·m
90 kN·m
45 kN·m
30 kN·m
M = wL²/8 = 10 x 36 / 8 = 45 kN·m.
A simply supported beam of 8 m span carries a 20 kN point load at midspan. What is the maximum moment?
20 kN·m
160 kN·m
40 kN·m
80 kN·m
M = PL/4 = 20 x 8 / 4 = 40 kN·m. Using PL gives 160, which would be wrong.
A 3 m cantilever carries a 5 kN point load at its free end. What is the moment at the fixed support?
15 kN·m
5 kN·m
30 kN·m
7.5 kN·m
M = P x L = 5 x 3 = 15 kN·m. Maximum moment in a cantilever occurs at the support.
A 2 m cantilever has a uniform load of 4 kN/m. What is the moment at the support?
2 kN·m
8 kN·m
16 kN·m
4 kN·m
M = wL²/2 = 4 x 4 / 2 = 8 kN·m. Using wL² (16) forgets the 1/2 factor.
A 50 mm by 50 mm short column carries 150 kN axially. What is the compressive stress?
120 MPa
3 MPa
60 MPa
30 MPa
σ = P/A = 150 000 N / 2500 mm² = 60 MPa.
If the effective length of a slender column is doubled (all else equal), its Euler buckling load becomes:
Double
One quarter
Unchanged
One half
P_cr varies with 1/(KL)², so doubling the length divides the load by 4.
A beam's span is doubled with the same uniform load per length. How does its midspan deflection change?
It doubles
It increases by a factor of 16
It increases by a factor of 8
It increases by a factor of 4
δ = 5wL⁴/(384EI) grows with L⁴, so 2⁴ = 16.
A stable, statically determinate planar truss has 6 joints and 3 reaction components. How many members?
12
6
8
9
m = 2j - 3 = 12 - 3 = 9.
Using LRFD with 1.2D + 1.6L, what is the factored load for D = 20 kN and L = 30 kN?
72 kN
50 kN
80 kN
90 kN
1.2 x 20 + 1.6 x 30 = 24 + 48 = 72 kN. 50 kN is the unfactored sum.
A rectangular beam is 100 mm wide and 200 mm deep. If the moment is 10 kN·m, what is the maximum bending stress?
15 MPa
60 MPa
30 MPa
7.5 MPa
S = bh²/6 = 100 x 40000 / 6 = 666,667 mm³. σ = 10 x 10⁶ / 666,667 = 15 MPa.
A wall has layers with R-13 and R-5 in series. What is its total R-value and U-value (imperial)?
R-18 and U = 0.056
R-18 and U = 18
R-65 and U = 0.015
R-8 and U = 0.125
Series resistances add: 13 + 5 = 18. U = 1/R = 1/18 = 0.056.
A wall of U = 0.5 W/m²K and area 20 m² has a 20 K temperature difference. What is the heat loss?
2000 W
200 W
10 W
20 W
Q = U x A x ΔT = 0.5 x 20 x 20 = 200 W.
Which one of these changes would increase a rectangular beam's stiffness the most?
Doubling its depth
Adding a coat of paint
Using the same section in a longer span
Doubling its width
I = bh³/12, so doubling depth multiplies I by 8, whereas doubling width only doubles it.